Masonry repair
Sweep & inspection
Caps & crowns
Flue relining
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Tulsa Homeowners
A cracked crown, a rusted cap, or a flue that’s been leaking creosote into the masonry for years is the kind of problem that gets worse with every freeze and thaw in Tulsa. Our technicians have up to 10 years of experience with the repair systems the trade actually uses: DuraFlex liners, HeatShield resurfacing, Copperfield components. We handle chimney repair and nothing else, so the work stays inside our craft. We answer 24/7 at (833) 712-5506, with fast dispatch from 7am to 7pm, Sunday through Friday. Every repair starts with a camera inspection and a flat-price estimate you approve before we book, plus a photo report of what we found.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a protective cover over the flue opening to keep rain, birds, squirrels, and debris out of the chimney. You need a cap if your flue is open to the sky, if you’ve found nesting material during a sweep, or if water is staining the firebox after storms. We install Gelco and Famco caps because they hold up to Tulsa’s freeze-thaw cycles and hail better than the stamped hardware-store covers that rust through in a few seasons. A standard cap installation in Tulsa runs $180-$450, depending on the flue size, the number of flues, and whether the cap needs a custom base. The written estimate sets the final price.
Stainless Caps With a Lifetime Finish
We use stainless steel caps with mesh screens sized to the flue. Stainless doesn’t rust out the way painted galvanized covers do, which matters when spring storms roll through Tulsa County.
Custom Bases for Odd Flues
Not every flue is a clean rectangle, especially on older Tulsa homes. We fabricate a base to match the crown so the cap seals tight without gaps that let water in.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement is removal of a damaged or missing cap and fitting a new one that seals correctly. You need replacement when the existing cap is rusted through, dented from limbs or hail, missing its screen, or sitting loose after a wind event. We check the old cap’s base and flue clearance before installing a new Gelco or Famco model, since a new cap on a bad base just leaks again. Replacement in Tulsa typically runs $200-$500, with the range driven by cap material, flue count, and whether the base needs repair. The written estimate is the final word on price.
When Replacement Beats Repair
A cap with a cracked weld or a screen that’s pulled loose is usually worth replacing rather than patching. Once the metal has thinned, a patch won’t hold another winter.
Matching the Cap to the Flue
An oversized cap can trap moisture and let nesting birds back in through gaps. We measure the flue and match the cap so the fit is right from day one.
Chimney Liner Installation
Chimney Liner Installation is fitting a new flue liner inside the existing chimney to contain heat, gases, and creosote safely. You need a liner when the original clay tiles are cracked, when there’s no liner at all in an older Tulsa home, or when you’re switching to a different fuel or appliance that needs a properly sized flue. We specify DuraFlex and Olympia Chimney liner systems because they’re engineered for the heat and the flue geometry real chimneys have, not just straight drops. A full relining job in Tulsa runs $2,800-$7,500 depending on liner length, diameter, insulation, and the condition of the flue. That’s an estimate on a written quote, not a guess.
Why Liner Diameter Matters
An oversized liner lets gases cool and draft poorly; an undersized one chokes the appliance. We size the liner to the appliance and the flue, not to whatever’s on the shelf.
Insulation and the Cold Months
An insulated liner keeps flue gases hot enough to vent cleanly, which matters when Tulsa temperatures swing hard. It also protects the surrounding masonry from heat transfer.
Chimney Flashing Repair
Chimney Flashing Repair is fixing the metal or membrane seal where the chimney meets the roof, which is where most leaks start. You need it when you see water stains on the ceiling near the chimney, rust streaks on the flashing, or gaps where the roof meets the stack. We inspect the flashing carefully because it fails in ways that mimic other roof problems, and we use Copperfield flashing components where they fit the existing roof. Flashing repair in Tulsa runs $300-$900, depending on roof pitch, roof material, and how much of the flashing needs rebuilding. The estimate is written and flat-rate before we book.
Common Flashing Failures
Tar-smear repairs from past roofers crack and let water in. Failed step flashing, pulled nails, and rusted counter-flashing are the usual culprits, and each needs a different fix.
Roof Pitch and Material
A steep roof or metal roof calls for flashing built for that surface. The wrong flashing on a steep pitch just channels water under the shingles.
Chimney Crown Repair
Chimney Crown Repair is fixing the concrete or mortar cap at the very top of the chimney that sheds water and protects the flue. You need it when the crown is cracked, spalling, or pulling away from the stack, which lets water into the masonry and the flue below. We rebuild or resurface crowns with a sloped, durable mix so water runs off instead of soaking in, and we check the flue’s top seal at the same time. Crown repair in Tulsa runs $400-$1,200 depending on crown size, whether it’s a repair or full rebuild, and the condition of the masonry beneath. Written estimate, flat price, no surprises on the invoice.
Repair Versus Rebuild
A hairline crack can be sealed; a crown that’s crumbling or separating from the flue needs a rebuild. We tell you which one the evidence supports.
Why the Slope Matters
A flat crown pools water and cracks faster. We finish the crown with a proper slope so it sheds water the way it should.
Chimney Repair Companies
Chimney Repair Companies are the specialists you hire to fix chimney structure, liners, caps, and flashing rather than a general handyman with a truck. You need one rather than a generalist when the issue is structural, since the wrong fix on a flue or crown can create a fire or carbon monoxide hazard. Tulsa Chimney Cleaning works only on chimneys, using HeatShield for resurfacing, DuraFlex and Olympia Chimney for relining, and Gelco and Famco for caps. Chimney repair in Tulsa runs $250-$1,200 for most structural jobs, with relining and major rebuilds priced separately. Every estimate is free, written, and flat-rate.
Why Generalists Get It Wrong
A handyman can patch a crown or smear flashing, but the failure modes on a chimney are different from a roof. The materials and the heat loads aren’t the same.
What to Ask Any Chimney Contractor
Ask what system they use for resurfacing or relining, and whether they’ll show you the camera evidence. A pro answers both without hesitation.
Chimney Masonry Repair
Chimney Masonry Repair is fixing the brick, mortar, and stone of the chimney itself, from tuckpointing to rebuilding sections that have crumbled. You need it when mortar joints are recessed, bricks are spalling or flaking, or the stack is leaning from years of water damage. We repair masonry with matched materials and add a water-repellent finish only after the repair cures, since sealing a wet chimney traps moisture inside. Chimney masonry repair in Tulsa runs $500-$3,500 depending on the extent, from spot tuckpointing to a partial rebuild. We quote each job in writing after inspection so you know exactly what’s being fixed and why.
Tuckpointing and Spalled Brick
Recessed mortar joints let water drive into the stack. Repointing with the right mix and replacing spalled brick stops the damage before it reaches the flue.
Water Repellent, Done Right
A breathable water repellent keeps rain out while letting the masonry dry. Sealing a wet chimney with the wrong product causes more harm than good.
Brands We Service
We work with DuraFlex liner systems and know where the joints, insulation, and connectors wear first. We also install and repair HeatShield systems for resurfacing, and we know which flue conditions HeatShield will actually fix versus when a full reline is the honest answer. Those are the two brands that show up most often on Tulsa relining jobs, and we’ve handled both kinds of failures.
We also fit Gelco and Famco caps and flashing components, which are commercial-grade and hold up to Tulsa’s weather better than off-the-shelf covers. A cap that’s the right brand, sized, and installed right lasts far longer than a swapped-on generic one. Whether you have a DuraFlex liner, a HeatShield-resurfaced flue, a Gelco cap, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Water stains near the chimney or on the ceiling. This usually points to failed flashing or a cracked crown. Both get worse with every rain, so it’s worth having them looked at before the next storm.
- Crumbling mortar or spalling brick. Flaking brick and recessed joints mean water is already inside the masonry. Left alone, it can reach the flue and the framing.
- A cap that’s loose, rusted, or missing. An open flue lets in rain, birds, and debris that block the flue. That’s a draft and carbon monoxide problem waiting to happen.
- A crack in the visible flue tile. Cracked tiles let heat and gases into the surrounding structure. A camera inspection tells you whether it needs resurfacing or a full reline.
- Smoke backing into the room or a weak draft. Poor draft or smoke rollback can point to a liner or flue problem. It’s worth checking before you light the next fire.
Our Process, Step by Step
- 1
Book the visit and take a look. We start with a conversation about what you’re seeing, then schedule an inspection. We use a camera to see the flue, crown, and flashing up close, so the diagnosis is based on evidence.
- 2
Show you what we found. You get a clear explanation of the problem and a photo report of the actual condition. Nothing gets recommended that we can’t point to on the camera.
- 3
Write the estimate. The quote is flat-rate and written before any work begins. If part of the job can safely wait, we say so.
- 4
Do the repair with trade-grade materials. We use DuraFlex, HeatShield, Gelco, or Famco as the job calls for. Every repair is done to chimney standards, not general roof or masonry shortcuts.
- 5
Check the work and hand you the record. We verify the repair holds and give you the inspection and photo record for your files. That record helps with future sweeps and any insurance question.
How Much Does Chimney Repair Cost in Tulsa?
Chimney repair in Tulsa isn’t one price, because the jobs aren’t one job. A typical cap replacement runs $200-$500 depending on material and flue count. Flashing repair runs $300-$900, driven by roof pitch and how much flashing needs rebuilding. Crown repair runs $400-$1,200, and chimney masonry repair ranges from $500 to $3,500 depending on how much tuckpointing or rebuild is needed. A full reline is the bigger line item at $2,800-$7,500. Those ranges are estimates; the written estimate sets the final price.
What moves the price: the number of flues, the roof pitch and material, the condition of the masonry, and whether the job is a repair or a rebuild. Access matters too, since a chimney at the back of a steep roof takes more setup than a straight stack.
How to avoid overpaying: get the camera evidence before you agree to anything, and ask whether a HeatShield resurfacing can extend the liner’s life instead of a full reline. Sometimes it can; sometimes it can’t, and the camera tells you which. Our free estimate includes the inspection, a written flat price, and an honest answer about what can safely wait.
Our Service Area Near Tulsa
We serve Tulsa and the surrounding communities, including Catoosa, Turley, Jenks, Owasso, Bixby, Sand Springs, Glenpool, Sapulpa, Skiatook, Verdigris, and Collinsville. Most repair visits are scheduled within a few days of the inspection, and our technicians know the area’s housing stock and how chimneys here weather over time. If you’re outside Tulsa proper, we can schedule around your location. Our Tulsa Chimney Cleaning page covers the full service picture.
Serving Tulsa, OK – Our Local Coverage Area
We serve Tulsa and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Tulsa
Chimney repair is fixing the parts of a chimney that keep it safe and watertight, including the cap, crown, flashing, masonry, and liner. It’s different from a sweep, which clears creosote, and from an inspection, which diagnoses the condition. Most repairs start with an inspection so the fix is based on evidence, not guesswork. Call (833) 712-5506 for an exact quote; estimates are free.
Most cap, crown, and flashing repairs are done in a few hours to a single visit. Masonry repairs and relining can take longer, depending on the extent of the work and the weather. We give you a realistic time frame with the written estimate. Call (833) 712-5506 to schedule a free estimate.
Most chimney repairs in Tulsa run $200-$1,200, with relining at $2,800-$7,500 and major masonry work up to $3,500. The exact number depends on the part being fixed, the material, and access. You get a flat written price before we book. Call (833) 712-5506 for an exact quote; estimates are free.
Yes. We install and service DuraFlex liner systems and HeatShield resurfacing, along with Gelco and Famco caps. We know where each system wears and what condition it can and can’t fix. Call (833) 712-5506 for an exact quote; estimates are free.
Same-day repair is often possible when the schedule allows. We answer 24/7 at (833) 712-5506, with fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening.
Our repairs come with a satisfaction guarantee, and we back the workmanship on what we fix. The specific warranty for your job is spelled out on the written estimate. Call (833) 712-5506 for an exact quote; estimates are free.
Clear the area around the fireplace and hearth, and make sure we can get to the roof or chimney access point. If you’ve noticed water stains, loose bricks, or a draft problem, note where you see them. It helps us get straight to the diagnosis. Call (833) 712-5506 to schedule.
Schedule Your Chimney Repair Service in Tulsa Today
A chimney that’s leaking, cracked, or missing its cap won’t fix itself, and the cost only grows with each storm. Call (833) 712-5506 to book a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. You’ll get camera evidence, a flat written price, and an honest answer about what can safely wait. No-obligation estimates, and professional-grade materials on every repair. For related work, see our chimney repair overview, our chimney repair page for Catoosa homes, and our chimney repair page for Turley.
Written by the team at Tulsa Chimney Cleaning.